Oberon 1053-01 Manuel d'utilisateur télécharger pdf

Installation Instructions

Model Number 1053-01

(877) 867-2312 • www.oberonwireless.com

P/N 1507 – Rev. A 05/23/13 Oberon, Inc. •

••

• 1315 South Allen Street •

••

- Ceiling enclosure Model 1053-01 assembly – 1 each

- ¾” Trade size cable clamps – 2 each

- Plastic push pin fastener – 2 each

- Installation Instructions – 1 each

- Caddy Speed Link – 2 each

- Keys for access door lock – 2 each

- Fire Block Foam – 1 each

- Support wire – 4 each

If any of these items are missing, contact your Oberon representative.

Find a flat work surface to assemble the ceiling enclosure, access point and antenna(s) prior to mounting in ceiling.

Step 1 – Place the ceiling enclosure

assembly on the work surface with the

keyed doorway unlocked. Install either one

or two cable clamps as required per the

application (If using POE, only one clamp

will be required, if using separate power

supply, use two cable clamps and bring

power in through one cable clamp and

Ethernet in through the other). Figure 1.

Step 2 – Install antenna by inserting the

cables through the 1” dia. hole in the

center of the cover. After the cables have

been pulled through the door, place

rubber gasket (if included) on and thread

the plastic nut that comes with the

antenna until tight (reference Figure 2).

Page 2

Step 3 – Feed the Ethernet cable though the cable clamp and

attach to the AP. Next, use the 8-32 pan head screws to fasten

the Cisco AIR-AP-BRACKET-2 to the bottom of the back box.

Place the AP so the feet fit into the key slots on the mounting

plate. The AP should be aligned so that the “Cisco Logo” is right

side up (reference Figure 3).

Step 4 – After the AP is set in the enclosure, lock it in

place by sliding the AP down along the key holes until it

clicks into place. The AP will slide approximately ½”. Pull

up on the AP to verify that is properly latched. If you feel

the AP lift from the enclosure, open the locking plate and

adjust the AP so that all four feet fall into the key slots,

then slide the AP back into position (reference Figure 4).

The assembled unit is now ready for ceiling installation.

Step 4 – Remove the ceiling tile and replace it with the completed access point enclosure assembly.

Step 5 – Use the Caddy Speed-Links to attach the enclosure to a permanent structure within the ceiling per the

manufacturer’s instructions.

**IMPORTANT** - This is an important safety feature that could prevent human injury or damage to the access

point should the unit become dislodged from the ceiling.

Page 3

Figure 1 – Installation of cable clamps

Figure 2 - Installation of Cisco Antenna.

Figure 3 - AP Installation

Figure 4 - Lock AP in Place

1 2

Résumé du contenu

Page 1 - Installation Instructions

Installation Instructions Model Number 1053-01 (877) 867-2312 • www.oberonwireless.com P/N 1507 – Rev. A 05/23/13 Oberon, Inc. •••• 1315 South

Page 2 - **** WARNING ****

Step 6 – Run the data and power cable (if required) through the conduit connectors located on sides of

Commentaires sur ces manuels

Pas de commentaire

Oberon 1053-01 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires de communication Oberon 1053-01. Oberon 1053-01 User Manual [en] [fr] [de] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Oberon 1053-01