Oberon 1075-WA Manuel d'utilisateur télécharger pdf

Installation Instructions

Model Number 1075-WA

(877) 867-2312 • www.oberonwireless.com

Rev. A2 05/23/13 Oberon, Inc. •

••

• 1315 South Allen Street •

••

Figure 5 – Exploded door view.

Assembly Components:

- Ceiling enclosure Model 1075-WA assembly – 1 each

- Ceiling tile bridge – 2 each

- #8-32 X 1/4 “ screw –4 each

- #8-32 nut – 4 each

- 3/4” Trade Size Cable Clamp – 1 each

- Keys for access door lock – 2 each

- Support wire – 4 each

- Fire Block Foam – 1 each

If any of these items are missing, contact your Oberon representative.

Find a flat work surface to assemble the ceiling

enclosure, access point and antenna(s) prior to

mounting in ceiling.

Step 1 - Cut a 13” x 13” opening in the center of a

ceiling tile (not included – ref. Figure 1).

Step 2 – Place the ceiling enclosure assembly on the

work surface. Remove one of the 1” trade size hole

cover on the side of the enclosure and install the 1”

conduit nipple (the side on which the conduit nipple is

to be installed will be determined by the location the

enclosure is to be installed and direction from which

conduit will be brought into the enclosure – ref. Figure

2).

Page 2

Step 3 –Lay ceiling tile over the

enclosure assembly such that

the previously cut opening in the

ceiling tile is equally spaced

around the outside of the

enclosure (ref. Figure 3). Place

the ceiling tile bridges along

each side of the enclosure and

attach using a #8-32 screw.

Prior to tightening, be sure to

properly align the tile bridges so

the ends of the tile bridges align

with the outside edge of the

ceiling tile. Once the tile bridges

are properly aligned, press the

shoulder of the tile bridge down

firmly against the tile and then

securely tighten the screws.

This is to assure that there is

minimal gap between the

enclosure’s flange and the

ceiling tile once it is placed in

the ceiling. The four (4) holes on

the tile bridge will be used to

secure the enclosure with grid

wires.

Step 4 – Unlock and open the door. Use the

manufacturers T-Bar mount clip to attach the access point

to the T-Bar Section on the mounting plate. An additional

mounting plate provided by the manufacturer of the access

point may be needed to attach the access point (Figure 5).

Data cable(s) may need to be plugged in to the access

point prior to attaching to the mount. Cisco access points

use Cisco AIR-AP-BRACKET-2 for 2600/3600 series

access points and AIR-AP-BRACKET-1 for 1140/3500

series.

Page 3

Figure

Hardware installation.

Figure 3 - Installation to ceiling tile.

This product is Listed by Underwriters

Laboratories Inc. Representative

samples of this product have been

evaluated by UL and meet applicable

safety standards.

File #E348543

1 2

Installation Instructions 1

Résumé du contenu

Page 1 - Installation Instructions

Installation Instructions Model Number 1075-WA (877) 867-2312 • www.oberonwireless.com Rev. A2 05/23/13 Oberon, Inc. •••• 1315 South Allen Stre

Page 2

+ Step 5 – Remove the ceiling tile from the location where the access point enclosure is to be placed (if necessary) and replace with

Commentaires sur ces manuels

Pas de commentaire

Oberon 1075-WA Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires de communication Oberon 1075-WA. Oberon 1075-WA User Manual [pl] [en] [de] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Oberon 1075-WA