Oberon 1078-CCOAP Manuel d'utilisateur télécharger pdf

Installation Instructions

Model Number 1078-CCOAP

(877) 867-2312 • www.oberonwireless.com

Rev. B1 0/23/13 Oberon, Inc. •

••

• 1315 South Allen Street •

••

Figure 3 - Cable Clamp Installation

Figure 2 - Cutout Dimensions

Wall Bridge In Mounting Position

Figure 1 - Installation Into Wall/Ceiling

This product is Listed by Underwriters

Laboratories Inc. Representative

samples of this product have been

evaluated by UL and meet applicable

safety standards.

File #E348543

Figure 4 - Locked Position

Model 1078-CCOAP Locking Recess Wall/Ceiling Mount Assembly Components:

- Ceiling enclosure Model 1078-CCOAP assembly – 1 each

- Wall bridge – 2 each

- #8-32 X 3/8 “ screw – 4 each

- #8-32 nut – 4 each

- 3/4” Trade size conduit connector – 1 each

- Fire block foam – 1 each

- Keys for access door lock – 2 each

- Installation instructions – 1 each

- Eyebolt – 4 each

- Support wire – 4 each

If any of these items are missing, contact your Oberon representative.

Find a flat work surface to assemble the enclosure, access

point and antenna(s) (if needed) prior to mounting in wall or

ceiling.

Step 1 - Cut a 13” horizontal x 13.4” vertical opening in the

"hard lid" ceiling or wall (special cutting tools may be required –

ref. Figure 1).

Step 2 – Place the enclosure assembly on the work surface.

Remove one of the 1” trade size hole cover on the side of

the enclosure and install the 1” trade size conduit connector

(the side on which the trade size cable clamp is to be

installed will be determined by the location the enclosure is

to be installed and direction from which conduit will be

brought into the enclosure – ref. Figure 2).

Step 3 – Place the (2) two wall bridges in the mounting

position by loosing the (4) four wing nuts inside of the

enclosure. The position of the wall bridges will look like the

image in Figure 3. Place the enclosure in to the hole that

was cut in Figure 1. Angle the enclosure at 10° with the wall

bridges extended towards the bottom. The wall bridges will go in first. Once the bottom of the enclosure is in the hole push the

enclosure so it is flush with the wall or ceiling.

Page 2

Step 4 – Once the enclosure is flush with the wall or ceiling, slide the wall bridges in the L-slot, and draw the bridges against

the wall. Tighten the wing nuts one side at a time (Figure 4). At this point, the enclosure is ready to be "mudded" into the wall.

Additional material my be needed.

**IMPORTANT** - This is an important safety feature that could prevent human injury or damage to the access

point should the unit become dislodged from the wall or ceiling. Page 3

1 2

Résumé du contenu

Page 1 - Installation Instructions

Installation Instructions Model Number 1078-CCOAP (877) 867-2312 • www.oberonwireless.com Rev. B1 0/23/13 Oberon, Inc. •••• 1315 South Allen St

Page 2 - **** WARNING ****

Figure 5 – Exploded door view Figure 6 Step 5 –Unlock and open the door. Attach Cisco AIR-AP-BRACKET-1 for the 1140/3500 series APs

Commentaires sur ces manuels

Pas de commentaire

Oberon 1078-CCOAP Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Accessoires de communication Oberon 1078-CCOAP. Oberon 1078-CCOAP User Manual [it] [fr] [de] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires de communication Oberon 1078-CCOAP